Welcome to our website!

how to make the semi-automatic gear type tapping machine

SS-4508

 

The preface

 

Automatic tapping machine, is the gear tooth is apart from the tapping machine.With fast speed, high precision characteristics.

 

1 automatic operation:

 

During the tapping operations, if improper operation, especially tapping is soft material processing, may not be able to output perfect thread.Tapping machine to produce the best thread, must use the matching thread gear and rack.

 

2 automatic cycle (moving and loop and single)

 

When the depth of the thread tapping to need, due to the lower limit of the micro switch function, the spindle will automatically reverse, and will automatically turn the taps.Gearing cycle, the main shaft rotate automatically, and tap will automatically rotate, repeated cycle.A single cycle, after the spindle rotation and tap spin out, tapping homework about stop.

 

3 prevent tap broken two kinds of safety measures

 

If the friction is too big or to operate by the hole is too shallow, and the inner diameter of the processed material size does not conform to specifications, tap will easy to broken.In order to avoid accident and protect the tap, so this tapping machine gear clutch, with its principle of torque, friction to limit for too long.

 

When the tap is not aimed at the center of the hole, or have some difficulties in tapping screw tap will automatically stop, and reverse back to the origin.

 

4 vertical and horizontal tapping machine and multi-axis device

 

When multi-axis device installed in a vertical or horizontal tapping machine, operating efficiency can be doubled.This company produces the tapping machines, multi-axis device can device when using, if for different items processing center, the multi-axis device can be adjusted freely and change direction.

 

5 under severe operating motor will stop

 

Special motor and electric control system, and can reduce operation a week 1.5 seconds to 6.0 seconds.

 

6 propulsion power switch gear protective cover

 

When you move to promote gear protective cover, the power was cut off, while the main switch on.If forget to turn off the main switch, also can be at ease to change gear, single event must put back the cover cover good, otherwise can’t start the machine.

 

Instructions for

 

1, the power switch control.

 

(1) single cycle (a job completes, the machine will immediately stop).When the button is pressed, the single cycle is: forward – reversal – stop.(figure 1)

 

(2) the gearing cycle (a job to continue after the completion of job).When moving and cycle selection switch (figure 1) clockwise turn, circulation homework repeated start

automatically, according to counterclockwise rotation, the machine will stop after an operation.

 

Note: advancing the gear after the protective cover off, do the above (1) (2) operation, the motor can’t turn.

 

figure  1

2, the choice of the spindle speed

 

There are three stages of spindle rotation speed control with:

 

JH – 4508.

 

4 p motor power supply frequency, 1145, 855, 540:6 p/power supply frequency motor, 960, 570, 360

 

JT – 6516.

 

Power supply frequency of 60 hz, 720, 480, 300 / power supply frequency 50 hz, 590, 400, 250JT – 6532.

 

4 p power supply frequency 50 hz, 420 220 120/4 p 60 hz: 500 270 150 6 p power supply frequency 50 hz, 280 150 80/6 p 60 hz, 340, 180, 100

 

Split type 4508

 

Power supply frequency 50 hz: 1340 760 420

The frequency of 60 hz power supply: 1600 900 500

 

3, the locking screw pitch fixed gear change in advance

 

(1) in order to advance gear device, the location of the need to minimize the spindle sleeve, that is to say, press the power switch to single cycle operation, keep the spindlemoves down and stop at the lowest position after turn off the switch, when the reversal from the regulator to stop can determine the main shaft has been to the lowest position.

Why should check whether the main switch is turned off and the spindle in the lowest position?Because the spindle sleeve down as A result of the action of spring has A kind of pressure, if the spindle is not in the lowest position, shed advance gear wheel, A or B spindle will drop down rapidly, this risk must be avoided.Even before taking advance gear protective cover, didn’t turn off the main switch, the machine still does not work, even if the spindle has yet to reach the lowest position.Because in advance gear protective cover on the micro switch will automatically cut off power supply.Note: if the micro switch failure, the power can’t work, it is very dangerous, must observe the following principles: take out the forward gear protective cover before, please close the main switch off, push the gear off after the main switch to on.

(2) the gear oil AB two (to the) on the gear gear on A shaft, A gear on axis B B.In order to prevent errors of gear when placed, gear aperture of A and B is different, if the gear loading up on the main shaft trip to determine the position is not right.

 

 

 

 

 

figure 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

figure 3

 

4, by the regulator to adjust the distance

 

In order to adjust the main regulator must be mobile reverse distance.

 

(1) the structure of the stop is on the tablet is equipped with four holes screw head to lock or relax.

(2) the JT – 4508 trip optional within 10-45 mm.

(3) JT – 6516 and JT – 6532 spindle trip within 10-65 – mm.

Determine the trip after don’t make the cycle time more than effective limit range of the motor.

 

5, the nose of the vertical adjustment

 

(1) loosen the clamping screw (figure 4) handle operation (the nose have drills on the handle).

 

(2) when the head position is determined, must lock.

 

If must retire after tapping machines need or when tap must be put down to the lower position, so the spindle will not leave the center position.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

figure  4

The preface

 

Automatic tapping machine, is the gear tooth is apart from the tapping machine.With fast speed, high precision characteristics.

 

1 automatic operation:

 

During the tapping operations, if improper operation, especially tapping is soft material processing, may not be able to output perfect thread.Tapping machine to produce the best thread, must use the matching thread gear and rack.

 

2 automatic cycle (moving and loop and single)

 

When the depth of the thread tapping to need, due to the lower limit of the micro switch function, the spindle will automatically reverse, and will automatically turn the taps.Gearing cycle, the main shaft rotate automatically, and tap will automatically rotate, repeated cycle.A single cycle, after the spindle rotation and tap spin out, tapping homework about stop.

 

3 prevent tap broken two kinds of safety measures

 

If the friction is too big or to operate by the hole is too shallow, and the inner diameter of the processed material size does not conform to specifications, tap will easy to broken.In order to avoid accident and protect the tap, so this tapping machine gear clutch, with its principle of torque, friction to limit for too long.

 

When the tap is not aimed at the center of the hole, or have some difficulties in tapping screw tap will automatically stop, and reverse back to the origin.

 

4 vertical and horizontal tapping machine and multi-axis device

 

When multi-axis device installed in a vertical or horizontal tapping machine, operating efficiency can be doubled.This company produces the tapping machines, multi-axis device can device when using, if for different items processing center, the multi-axis device can be adjusted freely and change direction.

 

5 under severe operating motor will stop

 

Special motor and electric control system, and can reduce operation a week 1.5 seconds to 6.0 seconds.

 

6 propulsion power switch gear protective cover

 

When you move to promote gear protective cover, the power was cut off, while the main switch on.If forget to turn off the main switch, also can be at ease to change gear, single event must put back the cover cover good, otherwise can’t start the machine.

 

Instructions for

 

1, the power switch control.

 

(1) single cycle (a job completes, the machine will immediately stop).When the button is pressed, the single cycle is: forward – reversal – stop.(figure 1)

 

(2) the gearing cycle (a job to continue after the completion of job).When moving and cycle selection switch (figure 1) clockwise turn, circulation homework repeated start

automatically, according to counterclockwise rotation, the machine will stop after an operation.

 

Note: advancing the gear after the protective cover off, do the above (1) (2) operation, the motor can’t turn.

 

 

 

 

 

 

 

 

figure  1

 

 

 

 

2, the choice of the spindle speed

 

There are three stages of spindle rotation speed control with:

 

JH – 4508.

 

4 p motor power supply frequency, 1145, 855, 540:6 p/power supply frequency motor, 960, 570, 360

 

JT – 6516.

 

Power supply frequency of 60 hz, 720, 480, 300 / power supply frequency 50 hz, 590, 400, 250

 

JT – 6532.

 

4 p power supply frequency 50 hz, 420 220 120/4 p 60 hz: 500 270 150 6 p power supply frequency 50 hz, 280 150 80/6 p 60 hz, 340, 180, 100

 

Split type 4508

 

Power supply frequency 50 hz: 1340 760 420

The frequency of 60 hz power supply: 1600 900 500

 

3, the locking screw pitch fixed gear change in advance

 

(1) in order to advance gear device, the location of the need to minimize the spindle sleeve, that is to say, press the power switch to single cycle operation, keep the spindle

 

moves down and stop at the lowest position after turn off the switch, when the reversal from the regulator to stop can determine the main shaft has been to the lowest position.

 

Why should check whether the main switch is turned off and the spindle in the lowest position?Because the spindle sleeve down as A result of the action of spring has A kind of pressure, if the spindle is not in the lowest position, shed advance gear wheel, A or B spindle will drop down rapidly, this risk must be avoided.

 

Even before taking advance gear protective cover, didn’t turn off the main switch, the machine still does not work, even if the spindle has yet to reach the lowest position.Because in advance gear protective cover on the micro switch will automatically cut off power supply.

 

Note: if the micro switch failure, the power can’t work, it is very dangerous, must observe the following principles: take out the forward gear protective cover before, please close the main switch off, push the gear off after the main switch to on.

 

(2) the gear oil AB two (to the) on the gear gear on A shaft, A gear on axis B B.In order to prevent errors of gear when

 

placed, gear aperture of A and B is different, if the gear loading up on the main shaft trip to determine the position is not right.

 

 

 

 

 

figure 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

figure 3

 

4, by the regulator to adjust the distance

 

In order to adjust the main regulator must be mobile reverse distance.

 

(1) the structure of the stop is on the tablet is equipped with four holes screw head to lock or relax.

(2) the JT – 4508 trip optional within 10-45 mm.

(3) JT – 6516 and JT – 6532 spindle trip within 10-65 – mm.

Determine the trip after don’t make the cycle time more than effective limit range of the motor.

 

5, the nose of the vertical adjustment

 

(1) loosen the clamping screw (figure 4) handle operation (the nose have drills on the handle).

 

(2) when the head position is determined, must lock.

 

If must retire after tapping machines need or when tap must be put down to the lower position, so the spindle will not leave the center position.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

figure  4


Post time: Oct-16-2019